环亚

86000V/87000V

Characteristics

  • 环亚0.05% Accuracy*, 21,000 Samples/Sec

  • 200% & 400% Overload

  • 环亚300% Overrange

  • 0.0006%/oF Compensation

  • 3 kHz Data Bandwidth

  • Analog and FM Outputs

  • 环亚Digital Output with Temperature

  • 10 Units of Measure

  • 环亚14 Bessel Data Filters

  • 48 2S Max/Min Update

  • 环亚Interface Software Furnished

  • 环亚Zero Velocity Speed Pickup Options

  • Overview
  • Performance
  • Download
  • Contact

MCRT® 86000V Torque Transducers output shaft torque with 0.01% resolution. Digital, Analog and FM formats are simultaneously available. Industries highest overload and overrange ratings assure safety and accuracy even when the driveline has high peak to average torque ratios. Important features include non-critical installation, temperature data, max/min capture and absence of manual adjustments.


Code N Performance

Code C Performance

Torque Range

Factory Set @ Transducer Full Scale Torque. Field Resettable to any lower value; see Note 1.

Units of Measure

User may select from lbf-in, lbf-ft, ozf-in, ozf-ft, N-m, kN-m, N-cm, kgf-m, kgf-cm, gf-cm without re-calibration

Accuracy2 (nonlinearity, hysteresis & repeatability)

<±0.1 (End Point, % of Range)

<±0.05 (End Point, % of Range)

Bi-polar Shunt Calibration Enable

环亚From Stator Switches (one CW, one CCW), via TTL I/O, or PC Com Port using furnished software.

Zero Drift (% of Range/deg. F.)

<±0.002

<±0.001

Span Drift 环亚(% of Reading/deg. F.)

<±0.002

<±0.001

Temperature Ranges (deg. F.)

Compensated Range: +75 to +175; Usable Range: -25 to +185; Storage Range: -65 to +225

Rotor to Stator Maximum Misalignment (inches)

环亚Axial: ±0.4, Radial: 0.3; If Speed Pickup Option is installed then maximums may be reduced - call factory.

Rotational Effects 环亚(% of Range)

#±0.01

Analog Output Signals6, Auto-Scaled


MCRT® 86000V Full Scale Torque3

Default is ±10V with 50% overrange (±15V). User may select ±5V with 50% overrange (±7.5V). Caution: see Note 7.

MCRT® 87000V Full Scale Torque3

环亚Default is ±5V with 300% overrange (±15V). User may select ±10V with 50% overrange (±15V). Caution: see Note 7.

Signal Filter Cutoff Frequency4

Field selectable from 1 to 1 kHz in ten 1-2-5 steps plus 3 kHz selected from a remote PC using software furnished. Filters have Bessel Response; no delay distortion or overshoot errors.

Frequency Modulated Output, Auto-Scaled

Frequency: 10±5 kHz or 20±10 kHz or 40±20 kHz; field changeable (Default = 10±5 kHz); TTL square wave output.

Overrange (% of Range, see Application Note 20805)

环亚50 to 300; model/user selection dependent - see above. Applies to analog, Digital and FM (except for negative side) Outputs.

System Resolution (% of Range)

0.01

Output Noise, All Outputs (% of Range)

环亚<0.01 at 1Hz, <0.01 at 10 Hz, < 0.015 at 100 Hz, <0.028 at 1 kHz and <0.041 at 3 kHz.

System Response

环亚Torque is sampled @ 20 kHz. Its’ 3 db bandwidth is 3 kHz but can be reduced by filters (see above)

Rotor-to-Stator Transfer Rate

1.25 MBaud

RS232, RS422, RS485 Communications Port

环亚Com port outputs Torque and Temperature with units of measure. Inputs torque range if other than sensor full scale, selects units of measure, selects BAUD Rate, and permits remote computer control of the test.

BAUD Rate

环亚9,600 to 230,400 (default is 115,200); Drivers are protected for short circuit (current limit) and ±15kV ESD protected

Maximum Cable Length

RS232 = 50 feet, RS422/485 = 4,000 feet; 120 Ohm termination may be accessed via software.

Interface Software

环亚Provided to interface with Windows-based PC. Includes interconnect cable for a PC.

I/O Lines

环亚5 input and 2 output, all are user assignable. Default for 5 inputs are +CAL, -CAL, TARE, CLEAR TARE, and RESET MAX/MIN.

Status LED’s (on Stator Keypad)

Three Color Coded LED’s: Power (Yellow = Power-up, Green = OK, Red = Fault); Data (Green = OK, Red = Data Error); Rotor Temperature (Green = In Operating Range, Red = Out of Operating Range).

Keypad Control Switches

环亚+ CAL invokes CW Rotor Shunt Cal, -CAL invokes CCW Rotor Shunt Cal, Both held simultaneously for 5 seconds invokes TARE.

Rotor Temperature, Auxiliary Measurement

Rotor temperature is outpout via Comp Port. Range is 0 to 185 degrees F.; Accuracy is ±2 degrees. See above for status LED’s.

Option Code Z

30 to 180 pulses/revolution (model dependent) Zero Velocity Speed Pickup.

Supply Voltage/Power5

环亚10 to 26 VDC @ 6 Watts with Antenna aligned to 9 Watts with maximum specified misalignments


Related Products
var _hmt = _hmt || []; (function() { var hm = document.createElement("script"); hm.src = "https://hm.baidu.com/hm.js?e926529819a30f1e527282f563736c78"; var s = document.getElementsByTagName("script")[0]; s.parentNode.insertBefore(hm, s); })();